Surly Bikes Parts & Accessories

Rear disc brake adaptor specifically designed ONLY for the Surly Troll, Ogre and ECR. - For use with 160mm rotor only - Brake caliper must be 74mm post mount compatible

Pop this replacement headbadge on your Surly and it's good as new.

Surly made these handy plates for use with either the Long Haul or Disc Trucker frames, and only the Long Haul and Disc Trucker frames. They are to be used with a bicycle kickstand to keep your bicycle upright while not moving as if by magic. The plates consist of two halves that, when clamped on your frame in conjunction with a kickstand, protect your chainstays from hamfisting by sandwiching the frame between the plates. Have you ever eaten a hamfist sandwich? They taste terrible, so avoid them like the plague. - Compatible with 2019 and older Long Haul and Disc Trucker frames

Surly Stainless Steel Track Lockring. - Fits all but Campagnolo, Miche or Phil Wood - 5mm thick with 0.65mm lip for maximum thread and lockring wrench contact

This fine pair of Surly 10/12 Adapter Washers is designed to adapt any 135, 170, or 190mm O.L.D. QR axle hub with a 142, 177 or 197mm spaced thru-axle frame. Make sure the QR axle on your wheel is the right length for the frame spacing. For instance: 190mm OLD QR goes with 197mm thru-axle spacing.

This is Surly’s 29 x 3-inch Presta valve tube. It fits their Knard tires and is made of butyl rubber.

Surly Inner Tube to fit a wide range of plus-size and fat bike tires. - Labeled Size: 26 x 3.0 - 4.8 - Weight: 310 g - Valve Core: Removable - Shaft Type: Threaded - ISO Width (mm): 76mm–100mm - Tube Compound: Butyl - ISO Diameter: 559 / 26-inch MTN - Valve: Presta Short 32-40mm

Hey mang! I'm Flasky! You know, where ever I go people are always saying to me “Flasky, you're a good friend. You keep me warm when I'm cold, loose when I'm tight, and twirling when I should be sleeping.” Hey, I try! But I want people to know how tough I am! Not even a dog can hurt me! Well maybe a dog could, I don't know, like if it was maybe a pit-bull or something. Especially an alcoholic pit-bull who hadn't had a drink in a while. But still, I'm pretty tough cuz I'm stainless steel. I don't rust and I don't trap flavors like plastic. That way your gin don't taste like your juice. I'm a good size too; more than enough but never too much, except sometimes. So yeah, that's me. Let's go for a ride. Right now. C'mon, don't be stuck up. - Stainless steel. 6 oz (177ml)

Surly Thru-Axles are low-profile, bolted Thru-Axles are specifically designed for use with Surly thru-axle compatible frames. Offered in several sizes, for both front and rear wheels. 12x142 Rear Thru Axle: - Fits: Midnight Special and MDS Dropout bikes including Instigator, Legacy Karate Monkey & Legacy Krampus. 12x142/148 Rear Thru Axle: - Designed for frames with Surly Gnot Boost spacing (145mm), capable of working with 142 or 148mm rear hubs - Fits: Karate Monkey, Krampus, Troll, Ogre, ECR 12x177 Rear Thru Axle: - Fits: Wednesday 12x197 Rear Thru Axle: - Fits: Ice Cream Truck, Big Fat Dummy 12x100 Front Thru Axle: - Fits: Midnight Special 15x110 Front Thru Axle: - Fits: Karate Monkey, Krampus 15x150 Front Thru Axle: - Fits: Wednesday, Ice Cream Truck, Big Fat Dummy

The 12mm slotted MDS dropout is the newest chip for Surly's MDS equipped trail frames. You like chips, don't you? The 12mm slotted dropout chip uses a standard derailleur mount for maximum compatibility and is made of cast and machined 6061-T6 aluminum, with a fender eyelet. What's the coolest part about the 12mm slotted MDS chip, you ask? The fact that it also has the capability to run a 12 x 142mm thru-axle in a single speed configuration. This is good news because single speeds are good news. When you get an MDS equipped frame you're getting the option to set it up however you want. You can run a 142 x 12mm thru-axle rear end with a direct mount Shimano hanger, standard 135mm QR or The Mighty Singlespeed. The way this will work is that Surly complete bikes that feature the MDS will ship with whatever chip is compatible with derailleur spec. For instance, the complete Instigator 2.0 ships with the 142 x 12mm thru-axle Shimano chip. If you want to change it to a singlespeed later (and why wouldn't you?), all you have to do is get the SS chip. Frames will ship with all three MDS chips so pick your poison. The 142 x 12mm and 135mm QR chips are made of cast and machined 6061-T6 aluminum and The Mighty Singlespeed chip is 304 stainless steel, because the two words 'aluminum' and 'singlespeed' should never be too close to each other. Bad things can happen…. As you can see, the MDS gives you not just different build options, it lets you use a more varied selection of parts for your frame up builds. The MDS is featured on most of our trail bikes. That's right: Krampus Ops, Karate Monkey Ops, Instigator 2.0 and Ice Cream Truck frames all sport these puppies.

Surly Ultra New Axle Kits are for upgrading the internals of your existing Surly New hubs or replacing the internals on your Surly Ultra New hubs. -Compatible with Surly New hubs (upgrade kit) and Surly Ultra New hubs (replacement kit) - Each kit contains an axle, two 6901 cartridge bearings, two aluminum dust shields, two stainless steel cones, two stainless steel 6x1mm bolts, and two stainless steel bolt washers - Axle is quick release and bolt-on compatible; bolts included, QR is NOT included - Standard Surly New hubs come stock with 7901 bearings; this kit uses 6901 bearings which are non-angular

Pair this cog with your Shimano-compatible rear hub, spacers and a lockring (sold separately) and discover the joy and simplicity of a singlespeed without the cost of a new wheel. Machined from heat-treated chromoly and then chrome plated, these seriously tough cogs are strong, shiny and they come in sizes from 13T to 22T so you can pick the perfect gear.

The Moloko Adjunct Personal Effects Receptacle is made from urethane-coated nylon canvas and designed to fit in the center of the Surly Moloko Bar. It has space for essentials and can easily be accessed while riding. - Constructed from urethane-coated nylon canvas to provide water-resistant protection - Elastic cord on top snuggly secures extraneous loose items like wrappers or gloves - Integrated light port allows a battery cord to pass through - Dimensions: 254 x 90 x 90mm

The Surly Truck Stop Handlebar combines the benefits of a drop bar with those of a riser bar. Offering a variety of hand positions for comfort over the long haul, it also features 30mm of rise for a more upright and relaxed riding position. With a clean aesthetic, it’s a great option for taller riders looking for more rise and for bikes with a low-cut steer tube. - Lightweight, aluminum construction - Available in various widths - 31.8mm clamp diameter

The Surly Corner Bar is for off-road riders who want to give drop bars a try without swapping out the drivetrain and brake levers on their current mountain setup. Does that make it an economical option for fresh excitement on the trail? Yes, it does. - Chromoly steel with custom-butted tubing - 22.2mm grip diameter - 25.4mm clamp diameter - One set of 25.4/31.8 x 60mm Problem Solvers shims included

If variety is the spice of life, then the Moloko bar oozes umami at every bend. It offers a multitude of hand positions to keep you comfortable and in control over the course of a long day riding over varied terrain. It also has plenty of spots to mount your various accessories. Dangle a handlebar bag from it, strap some lights to it, throw a GPS on it (if that's your thing), and ride all day. It comes in a standard width of 735mm but if 685mm is more your style, don't you worry. Surly added cut marks so you can easily make it so. - Material: CroMoly steel - Clamp diameter: 31.8mm - Width: 735mm; Cut marks for 685mm - Rise: 0 - Sweep Angle: 34 degrees - Weight: 709g - Color: E.D. coated Black

Classic 100% chromoly construction and engineered for modern accessories, that's Surly's Long Haul Trucker Disc Fork. Its beautiful curved blades are brazed to a lovely and tough investment-cast crown and dropouts. There are disc-brake mounts and eyelets for fenders and mounts for a standard or low-rider rack. Plus, it boasts a tough powdercoat finish that's tres chic. - 100% CroMoly steel construction, curved blades, powdercoated - Extensive mounting options with threaded eyelets in four locations: double eyelet dropouts, mid-blade, and a pair drilled into the fork crown - 51mm IS disc brake mount - 700c has clearance for a 45mm tire